Super Street Network

Due to the EU’s Global Data Protection Regulation, our website is currently unavailable to visitors from most European countries. We apologize for this inconvenience and encourage you to visit for the latest on new cars, car reviews and news, concept cars and auto show coverage, awards and much more.MOTORTREND.COM
 |   |   |  120 Hours - Week to Wicked 2013 Subaru BRZ: Day 3
Subscribe to the Free

120 Hours - Week to Wicked 2013 Subaru BRZ: Day 3

We punctuate exterior mods with a GReddy front spoiler and prep for Day 4's big bump in power by installing a SPEC clutch and GReddy titanium exhaust

Bob Hernandez
Dec 5, 2019
Videographer: Ryan Foss

The third day of our Week to Wicked 2013 Subaru BRZ project build is in the books and we're moving along at a pretty good clip. After a couple days of chassis, brake, and cosmetic improvements, we've reached an important juncture in the story arc—getting ready for a boost in power scheduled for Day 4. For the build team, that meant wrapping up other sections of the car and laying down more groundwork for an increase in engine output.

We picked up a SPEC Stage 3+ clutch kit and 10-lb. billet aluminum flywheel for our Subie, but first we had to pull out the old unit, which was from a competing aftermarket brand. As you might imagine, dropping the transmission is a fairly involved operation and not for the faint of heart. In the cabin you're disconnecting the shifter and pulling out the center console, while in the engine bay and underneath the car you must unbolt the exhaust from the header back, slave cylinder, starter, and driveshaft. Then the gearbox is ready to unbolt and drop (hopefully on a trans stand, if you have one).

The SPEC Stage 3+ Clutch Kit package includes both release and pilot bearings, as well as a race bolt kit for the clutch. The Stage 3+ clutch features SPEC's high-clamp pressure plate and full-faced carbon-graphite disc. This configuration provides a street-friendly engagement, industry-best wear life, and manageability for different driving environments. The lightweight 10-lb. billet aluminum flywheel features a replaceable diamond ground high-carbon steel friction plate and stepped dowels.

120 Hours BRZ GReddy RS Ti exhaust tip Photo 37/37   |   120 Hours - Week to Wicked 2013 Subaru BRZ: Day 3

With the drivetrain ready for more power, we turned our attention to breathing and in particular ditching the stock exhaust system for something a little freer flowing. Our friends at GReddy Performance Products came to the rescue with one of its brand-new RS-Ti titanium cat-back exhausts. The beautifully manufactured single-exit setup is a 3-inch straight-through design and boasts an incredible weight savings, coming in at 12 pounds (the OEM exhaust weights 40 pounds). The system comes with all the hardware you need, too.

120 Hours BRZ GReddy front lip spoiler 01 Photo 37/37   |   120 Hours - Week to Wicked 2013 Subaru BRZ: Day 3

GReddy also came through with one of its new front lip spoilers for the BRZ. The hard urethane front piece features holes predrilled on the ends to screw right into place and also comes with double-sided tape to secure other sections of the spoiler. The lip extends the front lower edge of the car by some 17mm. Saving the day with a fresh coat of paint on the new bumper addition were our friends at PJ Bonafacio Autobody in La Puente, Ca., who tackled the very last minute request just in time.

120 Hours BRZ spark plugs coil plug Photo 37/37   |   120 Hours - Week to Wicked 2013 Subaru BRZ: Day 3

The last thing we did today was install new spark plugs for something special coming tomorrow (which we can't really talk about yet). This was our first time doing plugs on an H4 Subie engine, and boy, that sucked. You basically have just a couple inches between the frame rail and the cylinder head to work in - not fun. We did the driver side plugs from under the car and the passenger side plugs from above, and it only took us about 2.5 hours for the four (!) - longest spark plug change EVAR.

Day 3 is done and we are over the hump! Make sure to come back tomorrow for the next phase of the Super Street Week to Wicked/120 Hours Subaru BRZ.

For this build, the official sponsors of the Super Street Week To Wicked Subaru BRZ build, includes: Falken Tires, Konig Wheels, Greddy Performance Products, SPEC Clutch, Covercraft, Energy Suspension, Odyssey Battery, RS-R USA, and Vortech Superchargers

Follow the entire build

To see more behind the scenes photos, outtakes, and videos, search these hashtags on Facebook and Instagram:


By Bob Hernandez
924 Articles



Project K24's suspension gets an update courtesy of Fortune Auto, PCI and Circuit Hero
RodrezOct 22, 2020
We give you the quick rundown of how to troubleshoot suspected boost leaks.
Scott TsuneishiOct 22, 2020
For those who enjoy the audible, haptic feedback that comes from a snickety aftermarket shifter kit Hybrid Racing's Short Shifters offers the most diverse, innovative approach we've seen thus far from a bolt-in system.
RodrezOct 1, 2020
A step-by-step guide to knocking out parts powder coating projects in your home garage
Scott TsuneishiSep 17, 2020
Project K24 gets a new Mcleod Racing clutch/flywheel, refreshed transmission and Downstar Inc. hardware
RodrezSep 14, 2020
Sponsored Links